Filter cartridge: which size for a coffee machine or combi steamer?
The filter cartridge is bought, fitted — and four months later it is exhausted. Or it sits under the counter for two years because it was three sizes too large. Both cost money, and both have the same cause: the size of a filter cartridge cannot be read off the appliance, only off the water that runs through it. This guide shows which figure you need, why the same cartridge loses almost half its capacity depending on the appliance, and what the bypass setting on the filter head has to do with it.
The one figure that decides everything: carbonate hardness
Not total hardness. The capacity of a filter cartridge depends on carbonate hardness — the share of hardness that precipitates as limescale when water is heated. That is exactly what the ion exchanger in the cartridge captures, and exactly what exhausts it.
Every manufacturer capacity figure therefore quotes a reference hardness. At BWT water+more that is 10 degrees German hardness. If your water sits at 20 degrees, the capacity halves. At 5 degrees it doubles. There is no size that is right "for coffee machines" — only one that suits your water and your consumption.
You can get the carbonate hardness two ways: from your local water utility, which is obliged to publish it, or by measuring it yourself. Test kits for that cost a little over twenty euros. Anyone looking after several sites adds the analysis case with pH and conductivity meters.
A note on accuracy: the manufacturer states capacities with a tolerance of up to five per cent, depending on water quality and flow rate. So do not plan down to the last litre.
Same appliance, same cartridge — and still a different capacity
This is where things most often go wrong. Capacity depends not only on the water but on what your appliance does with it. Three cases, one and the same cartridge:
| Application | bestmax M at 10 °dH | Share |
|---|---|---|
| Vending machine without steam generation | 4,560 litres | 100 % |
| Hot beverage maker with steam generation | 3,800 litres | 83 % |
| Combi steamer, oven, ice maker | 2,620 litres | 57 % |
Between the vending machine without steam and the combi steamer there is a gap of almost 2,000 litres on the same cartridge. The reason is the bypass setting, more on that below. Choose the size from the highest figure in the data sheet and then fit it to a combi steamer, and you are left with an exhausted cartridge after barely half the expected service life.
The sizes at a glance
The range runs from X to 2XL. Capacities apply at 10 degrees carbonate hardness; height often decides as well, because space under the counter is rarely plentiful.
| Size | Vending, no steam | With steam | Combi steamer | Height | Price |
|---|---|---|---|---|---|
| X | 720 l | 600 l | 410 l | 287 mm | €51.50 |
| S | 1,200 l | 1,000 l | 690 l | 368 mm | €69.04 |
| V | 3,000 l | 2,500 l | 1,720 l | 429 mm | €74.37 |
| M | 4,560 l | 3,800 l | 2,620 l | 485 mm | €103.89 |
| L | 6,240 l | 5,200 l | 3,585 l | 512 mm | €132.18 |
| XL | 8,160 l | 6,800 l | 4,690 l | 512 mm | €156.78 |
| 2XL | 14,400 l | 12,000 l | 8,270 l | 576 mm | €216.64 |
Work out the price per thousand litres rather than per unit. The X costs a good €71 per 1,000 litres, the 2XL just under €15. The jump from S to V is the most striking in the whole range: two and a half times the water for a good five euros more. If you are torn between the two, take the V.
The bypass — why one cartridge has three capacities
The filter head lets you set how much water actually passes through the filter material. That setting is called the bypass and runs from 0 to 3.
At bypass 0 everything goes through the ion exchanger. Protection is at its maximum, capacity at its lowest. At bypass 3 a large share is routed past the filter and blended back in afterwards. The cartridge lasts longer but lets more hardness through.
So the bypass does not regulate service life, it regulates the result. A combi steamer needs clean steam and tolerates almost no residual hardness — there the bypass sits low, and that is the reason for the 57 per cent in the table above. Coffee water, by contrast, is not meant to be fully softened: without minerals the espresso lacks extraction and the taste goes flat. There a higher bypass is wanted.
Bypass and size therefore belong to one decision, not two in sequence. Turning the bypass up later to gain service life degrades the very thing the filter was bought for.
The filter head is bought separately — once
The cartridge cannot be connected on its own. It needs a filter head, and that is a one-off purchase: the head stays on the wall, the cartridge gets changed. With a universal filter head every size in the range fits the same head, so you can move from S to M later without reinstalling anything.
The bypass setting sits on the head as well. If you want to count consumption, add a water meter in line; otherwise only the calendar is left.
On the connection: the cartridges work at 2 to 8 bar inlet pressure and 4 to 30 degrees water temperature, with a 3/8 inch connection. If line pressure is higher, a pressure reducer belongs in front. The cartridges can be fitted upright or lying down, which helps under cramped counters.
When to change it
Whichever comes first: the capacity is reached, or six months are up. After twelve months at the latest the cartridge has to go, even if litres remain on paper. The filter material works wet, and activated carbon is not a component that keeps indefinitely.
A worked example, with the assumptions stated: a café serves 150 drinks a day, counted at 0.15 litres per drink, on 26 days a month. That is around 585 litres a month. At 10 degrees carbonate hardness and with steam generation, a bestmax M at 3,800 litres would last a good six months — right at the six-month limit. An S would be through in about six weeks. Put in your own figures; the order of magnitude shows why catering operations rarely buy below V.
Not every cartridge does the same job
Within the sizes there are different versions, and they solve different problems. The standard range lowers carbonate hardness and filters particles, chlorine and off-flavours across five stages. Alongside it there are versions against limescale and corrosion, versions with magnesium for remineralisation and taste, and dedicated cartridges for water dispensers and ice makers.
None of that changes the sizing logic — carbonate hardness, application and bypass stay the same. Only the capacity figures differ by range, and those are stated on each product.
Matching products from our range
- BWT Wasser Testkit PRO, €22.50, determines carbonate hardness before you buy
- BWT bestmax X, €51.50, 720 l at 10 °dH, 287 mm tall
- BWT bestmax S, €69.04, 1,200 l
- BWT besthead FLEX universal filter head, €69.04, one-off, fits every size
- BWT bestmax V, €74.37, 3,000 l — this is where the price jump pays off
- BWT Aquameter 3/8", €75.60, counts consumption instead of days
- BWT bestmax M, €103.89, 4,560 l, the most common size in catering
- BWT bestprotect M, €104.30, against limescale and corrosion
- BWT bestmax L, €132.18, 6,240 l
- BWT bestmax XL, €156.78, 8,160 l, same height as the L
- BWT bestmax 2XL, €216.64, 14,400 l, the cheapest litre in the range
Frequently asked questions
Where do I get my carbonate hardness?
From your local water utility — it is obliged to publish the figures, usually on its website or on the annual bill. If you want to measure it yourself, or look after several sites, use a test kit. What matters is carbonate hardness, not total hardness; the two can differ considerably.
Can I pick a larger cartridge and change it less often?
Only up to the six-month limit. Beyond that, extra capacity buys nothing, because the cartridge has to come out after twelve months anyway. A size whose calculated service life runs well past a year is money thrown away — better a size smaller and changed on time.
Does every size fit the same filter head?
With a universal filter head, yes. That is the point of the design: the head is installed once, and cartridges can be swapped within the range. So you can start with an S and move to an M later without touching the installation.
Do I need separate filters for coffee and for the combi steamer?
As a rule yes, or at least two different bypass settings. Coffee water should keep its minerals; clean steam in a combi steamer tolerates almost no residual hardness. If both appliances hang off the same line, the stricter requirement decides — and that is almost always the steamer.
What about a softening system instead of filter cartridges?
That is the other design, and it pays off at larger volumes or with very hard water. It is not a mail-order item, though: connection, installation and servicing belong in professional hands. The comparison of the methods is in the water treatment guide; we supply systems on request only.
Unsure about the size?
Send us three figures: your carbonate hardness, the appliance and the rough daily consumption. The size follows from that, and we will tell you which bypass setting fits.
If you do not know the hardness, start with the test kit — twenty euros that prevent a wrong order.
To the category: Filter cartridges
Related guides
- Water treatment: the three methods and when each fits
- Coffee machine: the appliance behind the filter
- Combi steamer: why clean steam makes different demands
- Ice maker: water quality and clear ice
- Descaling a coffee machine: what to do when no filter was fitted
Last updated on 13 November 2026.